In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Technically, yes Steve, the Electric Trailer Brake Assembly for Lippert ABS Hubs - 12" 5.2K - 7K #LC83PX will physically fit the same 4-bolt mounting flange and 12inch drums. But here’s the catch: if your hubs don’t have the ABS ring, then the…
The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…
Hi Jeff; I'm assuming you were able to identify the parts based on the axle tag or by pulling off the hubs and measuring. Did you verify that the grease seal had a 2.25" inner diameter? The #AKIHUB-655-6-EZ-K comes with a 2.25" ID…
To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…
To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…
Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…
The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…
Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…
There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
Yes, I am and thanks for the information. It looks like your Reliable 2700lb Torsion Axle 08351 has a 1-1/16" x 1-1/16" spindle. I have two options for replacements and which one you need is going to be determined by how big your PWC…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Technically, yes Steve, the Electric Trailer Brake Assembly for Lippert ABS Hubs - 12" 5.2K - 7K #LC83PX will physically fit the same 4-bolt mounting flange and 12inch drums. But here’s the catch: if your hubs don’t have the ABS ring, then the…
The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…
Hi Jeff; I'm assuming you were able to identify the parts based on the axle tag or by pulling off the hubs and measuring. Did you verify that the grease seal had a 2.25" inner diameter? The #AKIHUB-655-6-EZ-K comes with a 2.25" ID…
To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…
To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…
Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…
The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…
Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…
There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
Yes, I am and thanks for the information. It looks like your Reliable 2700lb Torsion Axle 08351 has a 1-1/16" x 1-1/16" spindle. I have two options for replacements and which one you need is going to be determined by how big your PWC…
Perfect for heavy-duty trailers, the 8 on 6-1/2 inch hubs and drums offer durability and a perfect fit for your trailer needs. Whether upgrading or replacing, these hubs ensure smooth rides and reliable performance, even on long hauls and challenging terr
Yes, these hubs are designed for easy installation, often described as direct fit and bolt-on. They come with all necessary components, making the process straightforward, even for those upgrading from a 6-lug to an 8-lug setup. This ease of installation saves time and effort.
These hubs are built to last, with many users reporting years of reliable use. However, regular maintenance, such as checking lug nut torque and inspecting for wear, is essential to ensure longevity. Galvanized options offer added protection against rust and wear, making them a great value.
These hubs excel under heavy loads, offering durability and consistent performance. They are designed to handle the stress of towing large equipment, ensuring your trailer remains stable and safe, even on challenging terrains like mountain passes or long highway stretches.
While these hubs generally perform well, some prefer upgrading to higher-quality bearings like TIMKEN for added reliability. It's crucial to ensure the bearings are well-greased and properly installed to prevent issues during long hauls, especially when carrying expensive equipment.
The 8 on 6-1/2 inch hubs are ideal for heavy-duty trailers, providing a robust fit for larger axles. They ensure stability and reliability, especially when towing heavy loads over long distances. This size is perfect for those looking to upgrade from smaller hubs or needing replacements for high-capacity trailers.
Filters
